Vehicles
81 not categorized PORSCHE 911 THERMOSTACan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.99970114540 Known as: o-ring 70 x 2 thermostat housing View/Change Diagram
From $10.50
Make a selection 96420725103 This hose connects the rear of the oil tank to the thermostat housing. We recommend replacing 2 qty. Clamps, part # 99951225202 when replacing this piece. Sold individually. 1 necessary per car. Please note: this will only fit the oil thermostat with part # 964 207 047 05 or 964 207 047 07 or 964 207 047 08. View/Change Diagram
From $18.00
Make a selection 96420725102 This hose connects the rear of the oil tank to the thermostat housing. We recommend replacing 2 qty. Clamps, part # 99951225202 when replacing this piece. Sold individually. 1 necessary per car. Please note: this will only fit the oil thermostat with part # 964 207 047 03 or 964 207 047 06. View/Change Diagram
From $20.80
Make a selection 90004202501 This is the snap ring that holds the thermostat into the waterpump. easily replaced with snap ring pliers. View/Change Diagram
From $2.15
Make a selection BAT005 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73 928 1978-82
$1,090.00
Make a selection BAT006 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,179.45
Make a selection 9A110630500 Known as: gasket thermostat View/Change Diagram
From $35.00
Make a selection
$1,429.98
Make a selection 94462402101 Inoperative cooling fans will cause over heating that may cause serious engine damage. You can quickly test your fans to insure that it is not a relay or switch by hot wiring the fan. If it turns on it is probably a bad thermostatic switch. If it does not, you need a new fan. View/Change Diagram
From $115.00
Make a selection 901107040GB The ultimate oil cooler kit for your larger than 2.4 liter conversion. Kit contains every hose, clamp, thermostat, cooler, and shroud you need for a perfect conversion, along with detailed instructions. Please indicate if original or aftermarket engine oil tank will be used. General Fitment914 1970-76
$2,067.00
Make a selection 92861313101 Known as: thermostat View/Change Diagram
From $39.95
Make a selection 92810632103
View/Change Diagram
From $11.81
Make a selection 95510611100 Known as: thermostat housing View/Change Diagram
From $204.88
Make a selection AC0890913 High temperature rtv black silicone in a convenient dispenser. Non-corrosive and low odor. Use for gasketing, pump-oil pans, valve covers, gear boxes, water pumps, thermostats, and transmission parts. General FitmentACCESSORY
$19.43
Make a selection BAT001 The mocal oil cooling kit for the Porsche 914-4 consists of a 25 row -10an oil cooler & 7/12" cooling fan with with a sp1t thermostatic sandwich plate and -10an aqp stainless hose and fittings. The cooler is mounted to the underside of the engine grille, the plastic rain pan can be removed or a hole the size of the cooler can be made in the center. The sp1t thermo. Sandwich plate mounts between the oil filter and the filter mount allowing oil flow to the cooler after 180 degrees. We supply enough aqp stainless oil hose and aircraft fittings to link the sandwich plate to the oil cooler. General Fitment914 1970-76
$570.00
Make a selection 92810623909 Lower radiator to thermostat housing View/Change Diagram
From $10.67
Make a selection 95810613100 Known as: lid thermostat insert View/Change Diagram
$46.09
Make a selection 94410705600 Known as: thermostat housing View/Change Diagram
$1,121.45
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |